Important: Use custom search function to get better results from our thousands of pages

Use " " for compulsory search eg:"electronics seminar" , use -" " for filter something eg: "electronics seminar" -"/tag/" (used for exclude results from tag pages)

Tags: Power, Factor, Correction, Power Factor Correction, Power Factor Correction ppt, Power Factor Correction pdf, power factor correction circuit, power factor correction capacitor bank, power factor correction calculation, power factor correction methods, power factor correction capacitors, power factor correction harmonics, power factor correction circuit diagram, power factor correction pfc, power factor correction induction motor,
Thread Rating:
  • 1 Votes - 5 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Power Factor Correction
Post: #1

I need technical seminar topic on the topic power factor correction
Post: #2

.pptx  POWER FACTOR CORRECTION.pptx (Size: 660.89 KB / Downloads: 476)


Submitted By:
Rajat Kumar Barik
Electrical Branch


1. Power factor is the percentage of electricity that is being used to do useful work
2. Power factor =Active power/Apparent power
3. Apparent power has two component:
(a) Active power
(b)Reactive power


o ACTIVE POWER: Active power does all the work.
o UNIT : kw
o P= v I cos
o REACTIVE POWER: I t is the pseudo power(false) power which flows from source to load during +ve half and load to source during “ve half cycle.
o UNIT : Kvar
o Q= v I sin


(A)Larger kva rating of equipment

Kva = kw / cos
If cos will decrease then kva rating will increase
So we have to make equipment larger which is expensive


=> I= (P/ VCOS)
If powerfactor will decrease then current will increase.
So for conducting heavy current we have to
install large size Conductor.

© Copper loss

At low power factor the current drawn by the system will increase. Due to increase in current the copper loss will increase .

(d) Poor voltage regulation

The large current in low power factor causes a high voltage drop and the voltage at the receiving side is low.
In order to keep the constant voltage at the receiving side we have to install extra equipment (voltage regulators) is required.



Reduce utility power bills :

(a) For consumer
: A consumer has to pay electricity charges for his maximum demand in Kva plus the unit consumed. If the consumer improves the power factor then there is a reduction in Kva requirement. So there will be a annual saving.

(b)For generating station
: Generating station is as much concerned with power factor improvement as the consumer . The generators in a power station are rated in Kva but the output will depend on Kw.
Increase system capacity
Improve operating characteristics (Gain voltage)
Improve system operating characteristics (Reduce line losses)
Types of power factor correction
Power factor correction can be made in three ways
Capacitor bank
Static correction
Bulk correction
Synchronous condenser
Phase advancer

(1) Capacitor bank

The power factor can be improved by connecting capacitors in parallel with the equipment operating at lagging power factor .
The capacitor (generally known as static capacitor ) draws a leading current and partly naturalized the lagging reactive component of load current. This raises the power factor of the load.

Capacitor bank

DIRECTION of current before compensation
Direction of current after using capacitor bank

(2) Synchronous condenser

o A synchronous motor takes a leading current when over excited and therefore behaves as capacitor .
o An over excited synchronous motor running on no load is known as synchronous condenser. When such machine is connected in parallel with the supply , it takes a leading current which partly naturalizes the lagging reactive component of the load. Thus power factor can be improved.


(3) Phase advancers:
Phase advancer are used to improve the power factor of induction motors .The low power factor of an induction motor is due to the fact that its stator winding draws exciting current which lags
behind the supply by an angle of 90 degree.
If the exciting ampere turn can provided from some other a.c source then stator winding will be relived of exciting current and the power factor can be improved.


Lastly after the completion of my seminar , I conclude that improvement of power factor is necessary in both consumer end and supplier point of view . In some industries penalty is charged due to low power factor. In some industries where power consumed by the load is low , high ratings of equipment s are required.
SVC technology and synchronous generator are used for the improvement of power factor.

Post: #3

.doc  Power Factor Improvement.doc (Size: 1.04 MB / Downloads: 266) This article is presented by:

Power Factor Improvement


The aim of this technical report is to introduce a summary for a study done for Al-Ameen Engineering College for power factor improvement. This report includes an electrical engineering background about the problem of power factor, including: the causes, the consequences, the economical importance for the energy saving for our college and for the Kerala State Electricity Board as well, and the theoretical solution for solving that problem.

The report links the theoretical solution with the real applicable solution through the study done by our project team for energy planning. This study includes a six months research done by our team, which represents an ideal methodology for solving this problem starting from defining the magnitude of the power factor problem until designing the equipment that can solve that problem.

The report represents all the points in simple terminology, according to the objectives of the electrical engineering degree course.
1.1 What Is Power Factor
Power Factor is the ratio between the real (kW) and apparent power (kVA) drawn by an electrical load. It is a measure of how effectively the current is being converted in to useful work output and a good indicator of the effect of the load current on the efficiency of supply system. Poor power factor results in increase load current draw that causes additional losses in the supply and distribution systems.

Power Factor (pf) =

Resistive devices, like electric resistance heaters and incandescent lights transform all the power supplied to the device into heat or useful energy. Inductive devices, like motors, use some of the power supplied to the device to energize the inductive windings and create a magnetic field. This power, called reactive power, is alternately stored and given up by the windings, but is not used to do actual work. When this happens, the line supplying power to the device now carries the actual power used by the device and the reactive power created by the device.
Actual power used by the device is measured in kW, reactive power created by induction devices is measured in kVAR, and the apparent power in the supply lines is measured in kVA.

Post: #4

.pdf  pf corrector.pdf (Size: 406.51 KB / Downloads: 401)

The new European Norms EN 60555 and the international standard IEC555 will impose a limit on the harmonic content of the input current of mains supplied equipment. In practice this will require the addition of a Power Factor Corrector (PFC) at the input of many types of mains operated electronic equipment, for example electronic lamp ballasts, TV power supplies and motor drives. A correctly designed PFC draws a sinusoidal input current from the mains supply, in phase with the mains voltage, and meets the EN60555 norm. It may also provide additional functions, such as automatic mains voltage selection and a regulation of the voltage supplied to the attached equipment. Size and cost optimization of PFCs must include the RFI filter on the input, which prevents interference being fed back to the mains. The addition of the PFC represents another switching stage in the system, meaning that larger amount of high frequency noise is applied to the mains than with a conventional rectifier/capacitor front end, and so additional RFI filtering is required. The amount of fitering needed can be minimized by choosing suitable modulation techniques and mode of operation of the PFC.
Post: #5

.pdf  POWERFAC.pdf (Size: 41.88 KB / Downloads: 235)
Power Factor Correction

W. Mack Grady
The University of Texas at Austin
Austin, Texas 78712
Robert J. Gilleskie
San Diego Gas & Electric
San Diego, California 92123


We are all familiar with power factor, but are we using it to its true potential? In this paper we
investigate the effect of harmonics on power factor and show through examples why it is
important to use true power factor, rather than the conventional 50/60 Hz displacement power
factor, when describing nonlinear loads.
Voltage and current harmonics produced by nonlinear loads increase power losses and, therefore,
have a negative impact on electric utility distribution systems and components. While the exact
relationship between harmonics and losses is very complex and difficult to generalize, the wellestablished
concept of power factor does provide some measure of the relationship, and it is
useful when comparing the relative impacts of nonlinear loads–providing that harmonics are
incorporated into the power factor definition.
Power Factor in Sinusoidal Situations
The concept of power factor originated from the need to quantify how efficiently a load utilizes
the current that it draws from an AC power system. Consider, for example, the ideal sinusoidal
situation shown in Figure
Post: #6

.pdf  final print pdf.pdf (Size: 1.93 MB / Downloads: 355)
Power factor correction (PFC) is a technique of counteracting the undesirable effects of electric loads that create a power factor that is less than one. Power factor correction may be applied either by an electrical power transmission utility to improve the stability and efficiency of the transmission network or correction may be installed by individual electrical customers to reduce the costs charged to them by their electricity supplier. In order to improve transmission efficiency, power factor correction research has become a hot topic. Many control methods for the Power Factor Correction (PFC) have been proposed.
Capacitive Power Factor correction (PFC) is applied to electric circuits as a means of minimising the inductive component of the current and thereby reducing the losses in the supply.
The introduction of Power Factor Correction capacitors is a widely recognised method of reducing an electrical load, thus minimising wasted energy and hence improving the efficiency of a plant and reducing the electricity bill.
Power factor control means to control the power factor with its rated value of 0.9 to 0.95 in any kind of the system where we want to control power factor.
The whole system is divided into 3 PART.
1. Manually operated Inductive loads.
2. PIC 18F4520 microcontroller with LCD.
3. Capacitor bank with relay driver card.
In this project we are going to control the power factor with the use of PIC 18F4520 microcontroller chip.
We are using step by step manually operated inductive loads and also with it‟s the relay driver card to turn the capacitor bank on.
The improved power factor is displayed on the 16*2 LCD modules with the use of microcontroller.
Post: #7
is it works finally?
plz help me in comparator circuit becz my project based on automatic power factor correction through seven sagment

Marked Categories : yhs ddc bd, ppt on power factor improvement in electrical machines, power factor consume ppt, power factor improvement technical seminar topics in pdf, disadvantage of low power factor, ppt download of power factor correction, i want to give technical seminar on power factor correction, seminar topic on phase advancer, power factor, power factor correction circuit used in generating stations, pawoer fector improvment, power factor correction, power factor improvement using pic microcontroller, power factor correction ppt, seminar report on power factor correction, full report on power factor correction, powerfactor correction by synchronous machines ppt,

Quick Reply
Type your reply to this message here.

Image Verification
Image Verification
(case insensitive)
Please enter the text within the image on the left in to the text box below. This process is used to prevent automated posts.

Possibly Related Threads...
Thread: Author Replies: Views: Last Post
Last Post: SmologonovLJ
  power point presentation on role of bacteriocin in food safety Guest 0 0 25-11-2018 02:56 AM
Last Post: Guest
Smile gearless power transmission system pdf Guest 6 1,594 16-04-2018 08:28 AM
Last Post: Guest
  chemometric wind power in france Guest 0 0 01-04-2018 03:54 PM
Last Post: Guest
Thumbs Up power alcohol pdf from agricultural wastes Guest 1 0 31-01-2018 11:25 AM
Last Post: dhanabhagya
  harnessing high altitude wind power full report computer science topics 8 87,937,058 25-01-2018 12:22 AM
Last Post: RobertAmund
  seminar report on latest trends in nuclear power station Guest 1 233 18-11-2017 10:46 AM
Last Post: jaseela123
  power electronics by gnanavadivel ebook pdf download Guest 3 0 17-11-2017 12:17 PM
Last Post: jaseela123
  PRE-PAID POWER CONSUPTION USING COIN BOX REPORT seminar flower 1 899 27-10-2017 01:01 PM
Last Post: nagaland 8pm today
  microcontroller based power management system in ppt Guest 1 0 25-10-2017 11:56 AM
Last Post: jaseela123
This Page May Contain What is Power Factor Correction And Latest Information/News About Power Factor Correction,If Not ...Use Search to get more info about Power Factor Correction Or Ask Here