Important: Use custom search function to get better results from our thousands of pages

Use " " for compulsory search eg:"electronics seminar" , use -" " for filter something eg: "electronics seminar" -"/tag/" (used for exclude results from tag pages)


Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
POWER SYSTEM PROTECTION pdf
#1

POWER SYSTEM PROTECTION


.pdf   POWER SYSTEM.pdf (Size: 128.58 KB / Downloads: 123)

Current Transformers :

Distinction between CT and conventional
transformers; Equivalent circuit and phasor diagrams;
errors; ALF; Voltage developed across CT secondary ; CT ratio; Short time withstand current; Bar
and wound primary CTs Classification based on application. (Metering, Protection and PS class.) ; CT
specification.

Potential Transformers :

Errors; voltage factor; connections (star, delta, open delta and ‘V’ connections); PT ratio; Insulation
level ; Classification based on application ( Metering, Protection class ) ; Protection of PT; PT
specification.

Fault Level Calculations :

Impedance diagram; per unit and percentage impedance; sequence components; impedance to be
considered for different network elements like generator, transformer, transmission line, motor, cable,
etc; default figures where data not available; fault calculation procedures; step by step fault level
evaluation exercise for phase fault and ground faults.

HT Motor Protection :

Major protection elements; thermal over load; over current vs overload; critical review of motor and
relay thermal characteristics; major short comings; locked rotor; speed switch; negative sequence;
unbalance vs negative sequence; short-circuit; ground fault (zero sequence); use of residual
connected CT and CBCT; differential protection; under voltage protection; under current protection;
special protection requirement for wound motor; rotor unbalance; additional protection for
synchronous motor; loss of field.

LT Motor Protection :

Causes for LT Motor damage, Bimetal overload relay, HRC fuses, cost effective Motor Protection
relay for contactor controlled motor, co-ordination between fuse and relay, Application of thermistors.

Generator Protection :

Protection elements; Stator over current; Stator earth fault (95% and 100% ); Differential High
impedance and low impedance schemes; Over voltage protection; Over fluxing protection; Rotor
earth fault; Field over heating; Loss of excitation; Bearing vibration; Motoring (reverse power and low
forward power) protection; Unbalanced armature current protection; Voltage controlled over current
protection; Voltage restrained over current protection; Under frequency protection, withstand times for
steam, hydro, DG and gas units; Comparison of protection practices from different references.
Reply
#2

The protection of the electrical system is a branch of electrical power engineering that deals with the protection of electrical systems from faults through the insulation of parts damaged from the rest of the electrical network. The purpose of a protection scheme is to keep the power supply system stable, isolating only those components that are in fault, while leaving as much of the network as possible still in operation. Therefore, protection schemes should be applied with a very pragmatic and pessimistic approach to compensation system failures. Devices used to protect faulty power systems are called protection devices.

Components

Protection systems generally comprise five components:
• Current and voltage transformers to lower the high voltages and currents of the electrical system to levels suitable for relays
• Protection relays to detect the fault and initiate a trip, or disconnection, order;
• Circuit breakers to open / close the system based on relay and automatic closing commands;
• Batteries to provide power in case of power disconnection in the system.
• Communication channels to allow the analysis of current and voltage on remote terminals of a line and allow remote tripping of equipment.

For parts of a distribution system, the fuses are capable of detecting and disconnecting faults. Faults may occur in each part, such as insulation failure, dropped or broken transmission lines, malfunction of circuit breakers, short circuits, and open circuits. The protective devices are installed with the aim of protecting the assets, and ensuring the continuous supply of energy.

The switch is a combination of electrical switches, fuses or circuit breakers used to control, protect and isolate electrical equipment. Switches can be opened safely under normal load current, while the protective devices can be safely opened under fault current.
Reply

Marked Categories : experiments in power system protection, power sytem protection experiments for undergraduates pdf, research topics on power systems protections pdf, overcurrent protection, electrical ground faults, power system protection pdf, power system protection, high impedance vs low impedance protection relay eng tips, motor overload relay,

[-]
Quick Reply
Message
Type your reply to this message here.

Image Verification
Please enter the text contained within the image into the text box below it. This process is used to prevent automated spam bots.
Image Verification
(case insensitive)

Possibly Related Threads...
Thread Author Replies Views Last Post
  harnessing high altitude wind power full report computer science topics 8 120,594,748 25-01-2018, 12:22 AM
Last Post: RobertAmund
  The Contourlet Transform: An Efficient Directional Multiresolution Image pdf seminar post 1 397 21-09-2017, 10:38 AM
Last Post: jaseela123
  Ball-shaped robots to Inspect nuclear power plants seminar projects maker 2 901 20-09-2017, 02:49 PM
Last Post: jaseela123
  Low Power, Energy- efficient Domino Logic Circuits project report helper 1 6,125,656 15-09-2017, 01:09 PM
Last Post: jaseela123
  A Series Active Power Filter Based on a Sinusoidal Current-Controlled Voltage-Source project uploader 1 2,329 14-09-2017, 03:47 PM
Last Post: jaseela123
  Introduction to Vibration Energy Harvesting pdf study tips 1 680 13-09-2017, 02:53 PM
Last Post: jaseela123
  Basic Experiments in PID Control for Non-electrical Engineers pdf project girl 1 3,942 13-09-2017, 01:42 PM
Last Post: jaseela123
  Power Quality Improvement Using DVR Seminar Report seminar code 1 628 13-09-2017, 11:04 AM
Last Post: jaseela123
  Pulse Width Modulated (PWM) Controller for 12 Volt Motors pdf seminar projects maker 1 798 13-09-2017, 10:51 AM
Last Post: jaseela123
  Application of High Power Thyristors in HVDC and FACTS Systems pdf project girl 1 546 09-09-2017, 01:03 PM
Last Post: jaseela123
This Page May Contain What is POWER SYSTEM PROTECTION pdf And Latest Information/News About POWER SYSTEM PROTECTION pdf,If Not ...Use Search to get more info about POWER SYSTEM PROTECTION pdf Or Ask Here

Options: