Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Protection and Relay Schemes
#1

Presented by
KALOLIA ALAP R


.ppt   RELAY AND PROTECTION SCHEME.ppt (Size: 530.5 KB / Downloads: 290)
What are Relays?
 Relays are electrical switches that open or close another circuit under certain conditions.
 Relay Purpose
 Relay Types
Electromagnetic Relays (EMRs)
 EMRs consist of an input coil that's wound to accept a particular voltage signal, plus a set of one or more contacts that rely on an armature (or lever) activated by the energized coil to open or close an electrical circuit.
 Solid-state Relays (SSRs)
 SSRs use semiconductor output instead of mechanical contacts to switch the circuit. The output device is optically-coupled to an LED light source inside the relay. The relay is turned on by energizing this LED, usually with low-voltage DC power.
 Microprocessor Based Relays
 Use microprocessor for switching mechanism. Commonly used in power system monitoring and protection.
How a Relay Works
 Sold-State Relay
 Advantages/Disadvantages
 Electromagnetic Relays (EMRs)
 Simplicity
 Not expensive
 Mechanical Wear
 Solid-state Relays (SSRs)
 No Mechanical movements
 Faster than EMR
 No sparking between contacts
Microprocessor-based Relay
 Much higher precision and more reliable and durable.
 Improve the reliability and power quality of electrical power systems before, during and after faults occur.
 Capable of both digital and analog I/O.
 Higher cost
Why A System Needs Protection?
 There is no ‘fault free’ system.
 It is neither practical nor economical to build a ‘fault free’ system.
 Electrical system shall tolerate certain degree of faults.
 Usually faults are caused by breakdown of insulation due to various reasons: system aging, lighting, etc.
 Electrical Faults
 majority are phase-to-ground faults
 phase-to-phase
 phase-phase-phase
 double-phase-to-ground
Advantages for Using Protective Relays
 Detect system failures when they occur and isolate the faulted section from the remaining of the system.
 Mitigating the effects of failures after they occur. Minimize risk of fire, danger to personal and other high voltage systems.
 Protective Devices Comparison
 Protective Devices Comparison
Circuit Breakers V.S. Relays
 Relays are like human brain; circuit breakers are like human muscle.
 Relays ‘make decisions’ based on settings.
 Relays send signals to circuit breakers. Based the sending signals circuit breakers will open/close.
 Protective Devices Comparison
Fuses V.S. Relays
 Relays have dif
ferent settings and can be set based on protection requirements.
 Relays can be reset.
 Fuses only have one specific characteristic for a individual type.
 Fuses cannot be reset but replaced if they blow.
 Protection and Relay Schemes
 Motor Protection
 Timed Overload
 Locked Rotor
 Single Phase and Phase Unbalance
 Other
 Motor Protection
Timed Overload
Solution:
 Therm
al overload relays
 Plunger-type relays
 Induction-type relays

Motor Protection
Timed Overload Protection

Timed Overload Definition:
Continuously operate motor above its
rated value will cause thermal damage to
the motor.
 Thermal Overload Relays
 Use bimetallic strips to open/close relay contacts when temperature exceeds/drops to certain level.
 Require certain reaction time
 Inverse time/current relationship
 Thermal Overload Relays
 Plunger-type Relays
 Fast reaction time
 Use timer for time delay
 Such as oil dash pot.
 Inverse time/current relationship
 Plunger-Type Relays
 Induction-type Relays
 Most frequently used when AC power presents
 Change taps to adjust time delay
 Induction-Type Relays
 Motor Protection
Stalling
Some Definitions…

 Motor Stalling:
 It happens when motor circuits are energized, but motor rotor is not rotating. It is also called locked rotor.
 Effects: this will result in excessive currents flow given the same load. This will cause thermal damage to the motor winding and insulation.
 Motor Protection
Stalling
 Similar types of relays that are used for motor timed overload protection could be used for motor stalling protection.
 Motor Protection
Single Phase and Phase Unbalance
Some definitions

 Single Phase:
 three-phase motors are subject to loss of one of the three phases from the power distribution system.
 Motor Protection
Single Phase and Phase Unbalance
Some definitions…

 Phase Unbalance:
 In a balanced system the three line-neutral voltages are equal in magnitude and are 120 degrees out of phase with each other. Otherwise, the system is unbalanced.
 Motor Protection
Single Phase and Phase Unbalance
These conditions will cause

 Motor winding overheating
 Excessive vibrations
 Cause motor insulation/winding/bearing damage
 Motor Protection
Single Phase and Phase Unbalance
These conditions will cause
 Motor winding overheating

 Excessive vibrations
 Cause motor insulation/winding/bearing damage
 Motor Protection
Single Phase and Phase Unbalance
 Motor Protection
Other
 Instantaneous Overcurrent
 Differential Relays
 Undervoltage
 Electromagnetic Relays
 Ground Fault
 Differential Relays
 Transformer Protection
 Gas and Temperature Monitoring
 Differential and Ground Fault Protection
 Transformer Protection
Gas Monitoring Relays:
 These relays will sense any amount of gas inside the transformer. A tiny little amount of gas will cause transformer explosion.
Temperature Monitoring Relays:
 These relays are used to monitor the winding temperature of the transformer and prevent overheating.
 Transformer Protection
Ground Fault
 For a wye connection, ground fault can be detected from the grounded neutral wire.
 Transformer Protection
Ground Fault and Differential Relay
 Generator Protection
 Differential and Ground Fault Protection
 Phase Unbalance
 Generator Protection
Differential and Ground Fault
 Generator Protection
Phase Unbalance
Some Definitions..
 Negative Sequence
Voltage example:
Generator Protection Phase Unbalance
Some Definitions..
Negative Sequence:
 The direction of rotation of a negative sequence is opposite to what is obtained when the positive sequence are applied.
 Negative sequence unbalance factor:
 Factor= V-/V+ or I-/I+
 Generator Protection
Phase Unbalance
 Negative Sequence Relay will constantly measure and compare the magnitude and direction of the current.
Conclusion
 Relays control output circuits of a much higher power.
 Safety is increased
 Protective relays are essential for keeping faults in the system isolated and keep equipment from being damaged.
Reply
#2
Protection and Relay Schemes


.ppt   Protection and Relay.ppt (Size: 276.5 KB / Downloads: 35)

What are Relays?

Relays are electrical switches that open or close another circuit under certain conditions.

Relay Purpose

Isolate controlling circuit from controlled circuit.
Control high voltage system with low voltage.
Control high current system with low current.
Logic Functions

Relay Types

Electromagnetic Relays (EMRs)
EMRs consist of an input coil that's wound to accept a particular voltage signal, plus a set of one or more contacts that rely on an armature (or lever) activated by the energized coil to open or close an electrical circuit.
Solid-state Relays (SSRs)
SSRs use semiconductor output instead of mechanical contacts to switch the circuit. The output device is optically-coupled to an LED light source inside the relay. The relay is turned on by energizing this LED, usually with low-voltage DC power.
Microprocessor Based Relays
Use microprocessor for switching mechanism. Commonly used in power system monitoring and protection.

Advantages/Disadvantages

Electromagnetic Relays (EMRs)
Simplicity
Not expensive
Mechanical Wear
Solid-state Relays (SSRs)
No Mechanical movements
Faster than EMR
No sparking between contacts
Microprocessor-based Relay
Much higher precision and more reliable and durable.
Improve the reliability and power quality of electrical power systems before, during and after faults occur.
Capable of both digital and analog I/O.
Higher cost

Why A System Needs Protection?

There is no ‘fault free’ system.
It is neither practical nor economical to build a ‘fault free’ system.
Electrical system shall tolerate certain degree of faults.
Usually faults are caused by breakdown of insulation due to various reasons: system aging, lighting, etc.

Advantages for Using Protective Relays

Detect system failures when they occur and isolate the faulted section from the remaining of the system.
Mitigating the effects of failures after they occur. Minimize risk of fire, danger to personal and other high voltage systems.

Protective Devices Comparison

Circuit Breakers V.S. Relays
Relays are like human brain; circuit breakers are like human muscle.
Relays ‘make decisions’ based on settings.
Relays send signals to circuit breakers. Based the sending signals circuit breakers will open/close.
Fuses V.S. Relays
Relays have different settings and can be set based on protection requirements.
Relays can be reset.
Fuses only have one specific characteristic for a individual type.
Fuses cannot be reset but replaced if they blow.
Reply

Marked Categories : protaction n relay scheme, protection relay scheme abstract, protection scheme, esquemas eletricos de reles altern ncia, protection and relay scheme, abstract of protection and relay scheme, seminar on electrical schemes, protection and relay schemes abstract, protection and relay schemes, protecton and relay schemes ppt, protection and relay schemes pdf, protection and relay schemes seminarproject, security and relay schemes ppt seminar, protection and relay scheme ppt, how electrical fault can be detected ppt, seminars on protection of relays, relay schemes, subject seminar topic on relays, microprocessor based relay, electrical relay ppt, relays,

[-]
Quick Reply
Message
Type your reply to this message here.

Image Verification
Please enter the text contained within the image into the text box below it. This process is used to prevent automated spam bots.
Image Verification
(case insensitive)

Possibly Related Threads...
Thread Author Replies Views Last Post
  Investigation and Analysis of Inception Voltage and Field Distribution seminar presentation 1 25,638,320 22-09-2017, 11:06 AM
Last Post: jaseela123
  STATIC OVERCURRENT RELAY REPORT project girl 1 3,065 13-09-2017, 10:33 AM
Last Post: jaseela123
  POWER SYSTEM PROTECTION pdf study tips 1 1,464 09-09-2017, 09:08 AM
Last Post: jaseela123
  Type 1, 2 and 3 Control Schemes PPT study tips 1 973 08-09-2017, 09:14 AM
Last Post: jaseela123
  Relay Driver Circuit Report seminar projects maker 1 800 07-09-2017, 10:21 AM
Last Post: jaseela123
  Wind Energy and Production of Hydrogen and Electricity — Opportunities for Renewable seminar tips 1 1,087 06-09-2017, 11:19 AM
Last Post: jaseela123
  synchronization and protection of alternators project uploader 1 2,842 31-08-2017, 01:13 PM
Last Post: jaseela123
  ADAPTIVE NETWORK PROTECTION IN MICROGRIDS Electrical Fan 0 8,521,436 25-08-2017, 09:32 PM
Last Post: Electrical Fan
  Review on Protection Issues with Penetration of Distributed Generation in Distributio mkaasees 0 191 02-11-2016, 11:07 AM
Last Post: mkaasees
  SURGE CURRENT PROTECTION USING SUPERCONDUCTOR mkaasees 0 218 05-10-2016, 03:24 PM
Last Post: mkaasees
This Page May Contain What is Protection and Relay Schemes And Latest Information/News About Protection and Relay Schemes,If Not ...Use Search to get more info about Protection and Relay Schemes Or Ask Here

Options: